Skip to main content

Filter By:

  • Show More Brands

  • Show Fewer Brands

Other

$499.00
The absoluteBLACK's HOLLOWcage® for SRAM eTap AXS RED and Force 12-speed derailleurs makes the AXS drivetrain whisper quiet. It features a carbon-polymer mono-plate construction with bespoke, oversized, full ceramic bearings and one of the most advanced silencing pulleys ever made. - Designed for use with SRAM RED and Force AXS drivetrains - The Silent Xring Pulley dampens the chain impact on the guide pulley teeth, eliminating the engagement noise - Incredibly silent (over 12dB noise reduction vs stock) - HOLLOWcage uses full ceramic bearings (Silicon Nitride ceramic balls and Zirconia Oxide ceramic races) that make the guide pulleys incredibly stiff for greater shifting precision - One of the lightest oversized cages on the market (69g) - Works with 10-28t, 10-33t, and 10-36t cassettes - Not compatible with SRAM XPLR or 11-speed RED/Force - ONLY works with AXS flat top chain
$349.99
5-Speed Sturmey Archer Coaster Brake Trike Conversion Kit - 21T Front Drive Cog - 22T Rear Transfer Cog - 24T Axle Drive Cog - Cable stop required when installing on Sun Atlas Industrial Cargo Trike
$298.00
- Includes 61803 (1) and 61903 (1) bearings and one grease syringe - Measurable wattage savings between 1.5 and 9 watts per bearing set, depending on the level and condition of your existing bearings - Note: 88 front and 188v9 rear hubs are on all 2014 and newer Zipp 202, 303, 404, 808 - One kit required for: Zipp Super-9, 900 tubular and Sub-9 disc rear hubs
$298.00
- Includes 61803 bearings and one grease syringe - Measurable wattage savings between 1.5 and 9 watts per bearing set, depending on the level and condition of your existing bearings - These 61803 bearings are not interchangable with the 88/188 hub 61803 bearings
$356.00
The Charger 2.1 damper upgrade kit allows the fork to ride higher in the travel on compression while keeping the tires planted to the ground for unmatched control. - Includes complete right side internals
$269.00
The Charger 2.1 damper upgrade kit allows the fork to ride higher in the travel on compression while keeping the tires planted to the ground for unmatched control. - Includes complete right side internals
$334.00
Transform your existing Fox 36 suspension fork into the ultimate trail fork. The ACS3 coil conversion kit combines small bump sensitivity, traction, and mid stroke support of a coil with the big hit performance of an air spring. By using coil springs, you can eliminate the constant maintenance required to keep your fork running optimally! - Reduced friction for smoother overall fork performance - Air Bump Stop cartridge technology to control the bigger hits towards the end of the travel
$279.00
Replacement Pulley Wheels for the CeramicSpeed OSPW System. Includes 2 pulley wheels. - Precision-machined aluminum pulleys - For use with CeramicSpeed's Oversized Pulley Wheel System only - Coated races increase bearing service life by increasing hardness of race and reducing corrosion - CeramicSpeed products with coated bearings include a 6-year warranty
$356.00
The new Charger 2.1 damper upgrade kit allows the fork to ride higher in the travel on compression while keeping the tires planted to the ground for unmatched control. - Upgrades Charger 2.1 RC2 with crown high speed, low speed compression (includes complete right side internals) - Compatible with Zeb A1+ (2021+)/Domain B1+ (2022+)- Includes complete right-side internals
$404.00
- Charger 2.1 RC2 damper featuring independent high and low speed compression adjust - Includes complete right-side internals - Compatible with 2010+ BoXXer forks
$269.00
The lightest production damper. Ever. Performance packed with a rock-solid lockout to power up climbs and smash through sprint finishes. - Every detail machined and optimized to save on weight and maximize your performance - Factory tuned compression (in open position) provides the highest level of XC performance, precision and control - Maximum efficiency with a rock-solid lockout
$269.00
The lightest production damper. Ever. Performance packed with a rock-solid lockout to power up climbs and smash through sprint finishes. - Every detail machined and optimized to save on weight and maximize your performance - Factory tuned compression (in open position) provides the highest level of XC performance, precision and control - Maximum efficiency with a rock-solid lockout
$214.00
The 35c+ extensions offer a slightly higher rise then the orginal T4c and are half the weight - saving 12g in their uncut form. The new range of extensions have evolved from our well proven T-Series. They have been designed to offer distinct fit options. We have also adopted a new naming system whereby the name gives the angle material of the extension. Thus 35c+ is a 35° bend in aluminium. Performance: The sole purpose of extensions is to provide a comfortable position for the rider's hands relative to the armrests. They enhance performance by allowing the rider to relax into their optimal position, which is why we provide different fit options so each rider can chase their best performance. Fit Data: - Extension Shape: A 35 degree ski-bend extension suited to riders who prefer to adopt a wrist angle that is on the low side of the neutral range. - The 35c+ is a straight 35° bend. - Length: 400mm - Outer Diameter: 22.2mm - Inner Diameter: 19.4mm - Construction: Carbon - Weight: 142g/pair Tech Guide: - All the extensions have a 22.2mm diameter in the clamping area. - They are designed for cables to be routed out the rear of the extensions so do not have cable exit holes. Who is it for? The extensions will fit in any aerobar that is designed for 22.2mm. So can be used by any rider wishing to improve the comfort of their aerobar grips.
$214.00
The Subsonic/Race/35a aerobar combines the low stack Subsonic bracket with the arm-hugging Race armrest to offer an industry-leading fit range oriented towards low, narrow positions. The 35a extension offers a comfortable 35 degree angle with a 80mm rise. This is the only low stack clip-on in the market that maintains the pad-to-grip angle as the bar is stacked up Subsonic is not just another aerobar bracket. It brings our next-generation fit range to a low stack bracket design. This allows the bar to use our riser kits to increase the stack without changing the relationship between the armrest and the grips. The Race armrest has been designed to tightly cup the riders arms – facilitating a narrow position and increasing control at speed. Performance - The Subsonic/Race is designed to achieve a lower stack height than standard aerobars, without the added frontal area of a below-the-basebar extension clamping system. This improves aerodynamics and the fit range. Fit Data - Armrest offset: -85mm to -17.5mm in 7.5mm steps - Armrest Width: 142mm to 272mm in 18.5mm steps (with Extensions at 100mm) - Armrest Stack: The minimum is 40mm and the bracket is compatible with our existing risers which add up to 70mm of stack in 5mm increments. - The extension rotation can be easily adjusted using the shaft bolt. There is a 40mm range of extension length adjustment once the extensions have been cut. There are 80 distinct position options achievable just by moving the armrests. Combine that with the risers and this bar offers 1200 possible configurations. As a clip on bar it is also possible to adjust the extension width and tilt easily. This is the most adjustable low stack clip-on on the market. Origin Story After we released the Supersonic (J5) as a premium bracket with market leading fit options and verstility we wanted to bring the same kind of options to teh rest of our range of brackets and thus aerobars. Where our supersonic and Sonic brackets have a minimum stack of around 60mm, like most of the popular aerobars - we wanted the Subsonic to offer a substantially lower position. This helps the segment of the market who struggle to get into their ideal position with modern bike frames. And it was vital that we include stack height adjustment without altering the pad grip relationship - so our riders have the ability to fine-tune every aspect of their setup. The Race armrest shares the flippable design of the rest of our new generation armrests. By swapping sides or rotating the armrest, smaller increments of movement are achieved - making it simple to fine-tune a rider's position or match the position from their previous aerobar or bike. Additionally, there are two thicknesses of cushion available to ensure a snug fit for different sized arms. Who is it for - This bar is perfect for riders who wish to achieve lower positions than are possible with standard aerobar designs. Unlike other low stack bars, it allows fine-tuning of the stack height so the rider is not limited to only one armpad height. With the Race armrests fitted, it is tailored towards riders who intend to be low and narrow to punch the smallest possible hole through the wind. - Bracket: Subsonic - Clamp Diameter: 31.8mm (26.0 w/Shims) - Armrest: Race / 5mm Pads - Extension Length: 350mm - Width: 142mm to 272mm - Weight: 590g
$262.00
The Supersonic bracket (previously know as the J5) is the first and premier model of the new generation Profile Design brackets. It offers easier adjustments and a greater fit range than anything that came before it. Pairing this bracket with the ergo armrest offers industry-leading fit options and greater comfort. With the 35c extensions, this aerobar is suited to riders who wish to adopt an aerodynamic arrowhead hand position. Performance - The Supersonic/Ergo platform is designed to give riders the freedom to find their best possible position with a huge range of independence adjustments. Fit Data - Armrest Offset: -85mm to -17.5mm in 7.5mm steps - Armrest Width: 124mm to 290mm in 18.5mm steps (With Extensions at 100mm) - Armrest Stack: 58.5mm (no riser kit) to 138.5mm in 5mm increments (With aftermarket Riser Kit) - There are 80 distinct position options achievable just by moving the armrests. Combine that with risers and this bar offers 1440 possible configurations. As a clip-on bar it is also possible to adjust the extension width and tilt easily. Origin The supersonic was the first of our generation brackets - resulting from careful analysis of the way riders use their aerobars and the adjustments that need to be made. The Ergo armrest is an integral part of the overall adjustability scheme. The dual-offset design (shared with Race and Boom armrest) gives the most precise adjustment range of any armrest on the market. This, along with the evenly curved shape, allows it to work well for the majority of riders. Extensions - Extension Shape: The 35c extensions offer a 35 deg ski bend shape. This facilitates a slightly turned-down wrist position to create a streamlined hand position. They are 400mm long and can be cut to size to suit nearly ever rider. They are drilled for rear-exit cable routing. - Bracket: Supersonic - Clamp Diameter: 31.8mm (26.0 w/Shims) - Armrest: Ergo / 10mm Pads - Armrest Width: 124mm to 290mm in 18.5mm steps (with Extensions at 100mm) - Armrest Offset: -85mm to -17.5mm in 7.5mm steps - Armrest Stack: The minimum is 58.5mm and the bracket is compatible with our existing risers which add up to 138.5mm stack with (70mm of spacers added)
$262.00
The Supersonic bracket (previously know as the J5) is the first and premier model of the new generation Profile Design brackets. It offers easier adjustments and a greater fit range than anything that came before it. Paring this bracket with the ergo armrest offers industry leading fit options and greater comfort. Performance The Supersonic/Ergo platform is designed to give riders the freedom to find their best possible position with a huge range of independence adjustments. Fit Data - Armrest Offset: -85mm to -17.5mm in 7.5mm steps - Armrest Width: 124mm to 290mm in 18.5mm steps (With Extensions at 100mm) - Armrest Stack: 58.5mm (no riser kit) to 138.5mm in 5mm increments (With aftermarket Riser Kit) - There are 80 distinct position options achievable just by moving the armrests. Combine that with risers and this bar offers 1440 possible configurations. As a clip on bar it is also possible to adjust the extension width and tilt easily. Origin - The supersonic was the first of our generation brackets - resulting from careful analysis of the way riders use their aerobars and the adjustments that need to be made. - The Ergo armrest is an integral part of the overall adjustability scheme.The dual - offset design (shared with Race and Boom armrest) gives the most precise adjustment range of any armrest on the market. This, along with the evenly curved shape, allows it to work well for the majority of riders. Extensions - Extension Shape: The 4525c extensions offer a 45 deg lower and 25 deg upper section with a 7.5mm lateral shift per side. This allows the rider to choose between a low, short reach position or a high hands, stretched position for aerodynamics. They are 400mm long and can be cut to suit nearly every rider. They are drilled for rear-exit cable routing. - Bracket: Supersonic - Clamp Diameter: 31.8mm (26.0 w/Shims) - Armrest: Ergo / 10mm Pads - Armrest Width: 124mm to 290mm in 18.5mm steps (with Extensions at 100mm) - Armrest Offset: -85mm to -17.5mm in 7.5mm steps - Armrest Stack: The minimum is 58.5mm and the bracket is compatible with our existing risers which add up to 138.5mm stack with (70mm of spacers added)
$262.00
The Supersonic bracket (previously know as the J5) is the first and premier model of the new generation Profile Design brackets. It offers easier adjustments and a greater fit range than anything that came before it. Paring this bracket with the ergo armrest offers industry leading fit options and greater comfort. Performance The Supersonic/Ergo platform is designed to give riders the freedom to find their best possible position with a huge range of independence adjustments. Fit Data - Armrest Offset: -85mm to -17.5mm in 7.5mm steps - Armrest Width: 124mm to 290mm in 18.5mm steps (With Extensions at 100mm) - Armrest Stack: 58.5mm (no riser kit) to 138.5mm in 5mm increments (With aftermarket Riser Kit) - There are 80 distinct position options achievable just by moving the armrests. Combine that with risers and this bar offers 1440 possible configurations. As a clip on bar it is also possible to adjust the extension width and tilt easily. Origin - The Supersonic was the first of our generation brackets - resulting from careful analysis of the way riders use their aerobars and the adjustments that need to be made. - The Ergo armrest is an integral part of the overall adjustability scheme. The dual - offset design (shared with Race and Boom armrest) gives the most precise adjustment range of any armrest on the market. This, along with the evenly curved shape, allows it to work well for the majority of riders. Extensions - Extension Shape: The 50c extensions offer a 50 deg ski bend shape with a 7.5mm (per side) lateral shift. This allows a neutral wrist angle with the capability to fine tune the grip width. They are 400mm long and can be cut to suit nearly every rider. They are drilled for rear-exit cable routing. - Bracket: Supersonic - Clamp Diameter: 31.8mm (26.0 w/Shims) - Armrest: Ergo / 10mm Pads - Armrest Width: 124mm to 290mm in 18.5mm steps (with Extensions at 100mm) - Armrest Offset: -85mm to -17.5mm in 7.5mm steps - Armrest Stack: The minimum is 58.5mm and the bracket is compatible with our existing risers which add up to 138.5mm stack with (70mm of spacers added)
$199.99 - $255.00
Profile's T5+ Clip-on Aerobars are made of feathery light carbon fiber and feature super-shallow 15-degree ski-bend extensions with length, width, and armrest adjustments so you can easily find a perfect aero position. These clip-ons have Profile's J4 brackets for a low, aero arm position and their comfy, adjustable F-35 armrests.
$249.00
The V2+ Carbon introduces a new extension paired with the new L2 bracket. The V2+ extension is built up on a variation of the T2+ extension bend, featuring a higher rise S-bend to compensate for the lower mounting position of the extensions. The low stack bracket places the extension below the basebar with a stack height of 2.25cm below the T-series aerobars. Combining the L2 bracket and F40TT armrest offers small incremental adjustments, producing our best ever reach and width range. - Bracket: L2 Bracket - Armrest: F40tt - Armrest Stack: 37.5mm - Armrest Reach: -31.85mm to -76.85mm (7.5mm Increments) - Armrest Width (C-C): 183.2mm to 294.2mm (100mm Ext. Width) - Extension Length Adjustment: 211mm to 343mm (center of basebar to tip) - Extension Length: 366mm - Extension Height: 84mm - Extension Angle: 10° - Clamp Diameter: 31.8mm (26.0 w/Shims) - Weight: 550g
$249.00
The V4+ Carbon introduces a new extension paired with the new L2 bracket. The V4+ extension is a variation of the T4+ extension bend, featuring a higher-rise Ski-bend to compensate for the lower mounting position of the extensions. The clamp design places the extension below the basebar with a stack height of 2.25cm below the T-series aerobars. Combining the L2 bracket and F40TT armrest offers small incremental adjustments, producing our best ever reach and width range. - Bracket: L2 Bracket - Armrest: F40tt - Armrest Stack: 37.5mm - Armrest Reach: -31.85mm to -76.85mm (7.5mm Increments) - Armrest Width (C-C): 183.2mm to 294.2mm (100mm Ext. Width) - Extension Length Adjustment: 211mm to 343mm (center of basebar to tip) - Extension Length: 366mm - Extension Height: 84mm - Extension Angle: 30° - Clamp Diameter: 31.8mm (26.0 w/Shims) - Weight: 550g
Page 1 of 1